- #Tool Bar Right Side Of Sreen Mastercam X4 Manuals For Free
- #Tool Bar Right Side Of Sreen Mastercam X4 Software Requires A
Tool Bar Right Side Of Sreen Mastercam X4 Manuals For Free
Beginner F1 Tutorial Mastercam version 9. We have 98 Mastercam manuals for free PDF download. Mastercam Manuals Instruction Manual and User Guide for Mastercam.
It starts with two cabinets and builds a template for a granite top. Mastercam X4 FBM 1 Technical Support Bulletin: AllenCAD Tutorial Last Updated NovemAbstract: This tutorial demonstrates most of the features of AllenCAD necessary to design or modify a countertop using the program. What is New in Mastercam X6. Mastercam X5 Files and Mastercam. Mastercam X3 Post Parameter Reference.
Click on the new page in the startup assistant. Click on the standard tool bar (or file -> new menu command) and the startup assistance will be displayed. We start with a blank AllenCAD drawing. The cabinets are 54 x 24 and 48 x 29. We will be designing a countertop to fit over two cabinets to be placed in the center of a kitchen.
Enter 0, 0 for first corner and 54, 24 for opposite corner. Click on the rectangle tool on the draw toolbar (or draw -> rectangle). To start we draw two rectangles representing the cabinet outlines.
It turns magenta (purple). We click on the 2 nd cabinet to select it. Now we move the 2 nd cabinet into position by clicking on the move selected objects on the Allen Tile toolbar (or Modify -> move). Again click on the rectangle tool entering 0,0 and 48,29 for its corners. The outline of the 54 x 24 cabinet should appear.
We want to move the cabinet centered on the 54 inch bottom so we do a little math (54 48) / 2 = 3. This will allow us to move the 2 nd cabinet exactly into position. We will click on the tool on the options toolbar. The command window displays base point.
Tool Bar Right Side Of Sreen Mastercam X4 Software Requires A
You screen should now appear as follows:How to Download Free Mastercam Post Processors 2020-12-9 CAM software requires a post-processor to output. Click (File saved as tut1.flx) to display both cabinets. We enter 3, -29 for the move distance.
The tool is free to try.2 We decide we want an inch and a half overhang so we use the offset distance command to create the offset lines. This enhancement has been tested and released by the Quality Control Department and will function inside Mastercam X2. Mastercam X2 is an add-on that allows quick and easy one-click toggling on/off the visibility and active state of the Grid. This current computer was fine with x4 and x5, never had a problem but now all of a sudden it has a huge lag when I right click. This has been a problem for me with other computers in the past, with x2 ,x3 and x4.
Click on the fillet button on the modify toolbar (or Modify -> fillet). Now your drawing is as follows: (file saved as tut2.flx) We need to round off some corners so we use the fillet command on the top two corners. We repeat the command on the lower cabinet. At the prompt side to offset we want a line to the outside of the cabinet so we click outside the boundary of the rectangle. It turns magenta to indicate selected. Click on the upper cabinet.
(file saved as tut3.flx) To join the two vertical lines with a smooth curve, we will create two arcs of We want a 3 inch radius so the center of the first arc will be at +3,0 from the lower left corner or (1.5,-1.5). The top of the drawing now has rounded corners. Repeat modify fillet for top and right sides. Select the left side of the offset cabinet and then the top and a fillet will appear in the upper left corner. Enter 1 for the Fillet radius.
180 for start angle and 240 for end angle. For the center enter 1.5,-1.5. Click on the on the options toolbar.
We use sin(60) in equation below because we need to know vertical distance. We choose this angle so the two arcs meet in the center. File saved as (tut4.flx) 1 Geometry: cos(60 ) = 0.5.
Lets add some dimension lines on another layer. Tutorial Mastercam X Mill Manual INTRODUCTION 1 Mastercam X4 User.5 The counter top is done. Your new Moto X has a bright display that goes from one side all the way to the other. Merely said, the mastercam training guide. Access Free Mastercam Training Guide X4 Mill 2d Free the most less latency time to download any of our books like this one. Our digital library hosts in multiple locations, allowing you to get Page 1/10.
Click on Dim -> vertical (or the button on the dim toolbar). We put the dimensions on a different layer so it s easy to turn off the layer for cutting. In the drop down box select the dimension layer for new objects. Type in layer name dimension and click on new, and ok. This brings up the layer manager.
Click on pan on the Allen Tile toolbar (or View - > Dynamic Pan). Click top left corner after curve (-1 ½, 2 0 5/8). Right click to accept dimension Using Zoom extents, and zoom window, zoom to top left corner. Move mouse left to position dimension line and left click. Click on top corner (4 6 5/8, 2 1 ½). Click on the very bottom of the arc at /64, Then zoom extents and zoom window at top right corner of countertop.
(File saved as tut12.flx) To add text, click on the tool on the draw tool bar (or detail -> text) to start the text manager. Right click to accept dimension. Move mouse up to position dimension line and left click. Click on top right corner after curve (4 7 ½, 2 0 ½). Click hold mouse and drag screen to left repeatedly until the top right corner appears.
56 We note that the part number disappeared so we need to change its layer back to the default layer 0. Dimensions are turned off. Select the dimension layer from the list and click Off, Click OK. (saved as tut13.flx) To turn off dimension layer click on the layer manager tool on the property toolbar.
The tile program breaks our countertop into 3 pieces. Note the tile program picks up the part number and we select one tile line to have tiles continue through cutouts. The Allen Tile Options menu is displayed. (File saved as tut14.flx) Click on the button on the Allen Tile toolbar (or file -> Allen DirectCut tiling) and click on the button on the option tool bar, right click to indicate we are through selecting objects.
0 kommentar(er)
